[Jun 24, 2026] F5CAB4 Ultimate Study Guide - Actualtests4sure
Ultimate Guide to Prepare F5CAB4 Certification Exam for F5-CA in 2026
F5 F5CAB4 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
| Topic 6 |
|
| Topic 7 |
|
| Topic 8 |
|
| Topic 9 |
|
NEW QUESTION # 39
In the BIG-IP Configuration Utility, where can an administrator go to view a real-time, graphical overview of system performance, including CPU usage, memory utilization, and network throughput?
- A. Statistics > Dashboard
- B. Local Traffic > Virtual Servers
- C. Network > Interfaces
- D. Device Management > Overview
Answer: A
Explanation:
The Statistics Dashboard is the primary graphical interface used by administrators to monitor the real-time performance and health of the BIG-IP system.
* System-Wide Overview: Navigating to Statistics > Dashboard provides a centralized view of critical system-level metrics, including global CPU utilization (across all TMM instances and the Linux host) and total memory usage.
* Performance Tracking: In addition to CPU and memory, the dashboard displays other vital statistics such as total active connections, throughput (bits/packets per second), SSL transactions per second (TPS), and compression efficiency.
* Operational Health: Monitoring these metrics from the dashboard allows the administrator to quickly identify performance trends or resource exhaustion that could impact the Control Plane or Data Plane stability.
* Comparison to Other Menus:
* Local Traffic > Virtual Servers: Provides statistics specific to traffic objects rather than global system resources.
* Network > Interfaces: Shows physical layer statistics like link status, errors, and drops for specific ports.
* Device Management > Overview: Focuses on high availability (HA) states, synchronization status, and device trust rather than granular performance metrics.
NEW QUESTION # 40
When looking at this BIG-IP prompt: root@virtual-bigip1] Peer Time Out of Sync What does the message indicate? (Choose one answer)
- A. That the local time is correct, but the remote time is incorrect
- B. That one of the NTP sources has a skewed clock
- C. That there was a time synchronization issue between the BIG-IP device and its peer
- D. That the peer BIG-IP is unreachable for the device group
Answer: C
Explanation:
Comprehensive and Detailed Explanation From BIG-IP Administration Control Plane Administration documents:
On BIG-IP systems that participate in a Device Service Cluster (DSC), each device compares the remote device's system time to its own system time. If the difference is outside the ConfigSync time threshold (commonly referenced as 3 seconds by default), BIG-IP updates the shell prompt to show "Peer Time Out of Sync", and ConfigSync operations may fail until time is corrected (typically by fixing NTP reachability/configuration, or in some cases adjusting the threshold). (cdn.studio.f5.com) This message is specifically about time drift between peers in the trust domain/DSC-not basic reachability (so B is not what it means), and it does not prove which side is "correct" (so C is too specific). It also doesn't directly mean an NTP source is "skewed" (A can be a cause, but the prompt message itself indicates the peer-to-peer time mismatch condition). (cdn.studio.f5.com)
NEW QUESTION # 41
A BIG-IP Administrator reviews the Plane CPU Usage performance chart and discovers a high percentage of Control Plane utilization. Which type of traffic does this indicate a higher usage of?
- A. Accelerated
- B. Administrative
- C. Tunnel
- D. Application
Answer: B
Explanation:
Comprehensive and Detailed Explanation From BIG-IP Administration Control Plane Administration documents: F5 architecture distinguishes between the Data Plane (TMM processing application traffic) and the Control Plane (Linux host processing management tasks). High Control Plane CPU utilization typically points to administrative activities such as heavy GUI usage, complex API calls (iControl), large-scale configuration synchronizations, or intensive logging/monitoring tasks rather than the actual switching or load balancing of application data.
NEW QUESTION # 42
A BIG-IP Administrator makes a configuration change to a Virtual Server on the Standby device of an HA pair. The HA pair is currently configured with Auto-Sync Enabled. What effect will the change have on the HA pair configuration?
- A. The change will be undone when Auto-Sync propagates the config to the HA pair.
- B. The change will take effect when Auto-Sync propagates the config to the HA pair.
- C. The change will be undone next time a configuration change is made on the Active device.
- D. The change will be propagated next time a configuration change is made on the Active device.
Answer: B
Explanation:
Comprehensive and Detailed Explanation From BIG-IP Administratio24n Control Plane Administration documents: TMOS Device Service Cluste25ring (DSC) allows for configuration changes to be made on any device within a synchronization group. If Auto-Sync is enabled, the Control Plane detects the change on the Standby unit and automatically propagates (pushes) that updated configuration to the other members of the HA pair
NEW QUESTION # 43
What are the recommended methods for forcing a BIG-IP system to standby mode? (Choose two answers)
- A. Active BIG-IP: Configuration Utility > Device Management > Traffic Groups > Local Device (Self) > Force to Standby
- B. Active BIG-IP: CLI > tmsh run /sys failover standby
- C. Active BIG-IP: CLI > tmsh run /sys failover device standby
- D. Active BIG-IP: Configuration Utility > Device Management > Devices > Local Device (Self) > Force to Standby
Answer: C,D
Explanation:
BIG-IP provides two supported and documented methods to manually force a device into standby state in a high-availability (HA) configuration:
* CLI method (A):
* tmsh run /sys failover device standby
This is the correct and supported TMSH command to force the local device to transition from active to standby.
* Configuration Utility method (B):Navigating to Device Management > Devices > Local Device (Self) and selecting Force to Standby performs the same operation through the GUI and is fully supported.
Why the other options are incorrect:
* C is incorrect: Traffic Groups do not provide a "Force to Standby" option for the local device; traffic groups are used to manage which device owns specific traffic, not to force device-level failover.
* D is incorrect: tmsh run /sys failover standby is not a valid TMSH command. The correct syntax requires device standby.
Thus, the correct answers are A and B.
NEW QUESTION # 44
The BIG-IP Administrator suspects unauthorized SSH login attempts on the BIG-IP system.
Which log file would contain details of these attempts? (Choose one answer)
- A. /var/log/messages
- B. /var/log/audit
- C. /var/log/ltm
- D. /var/log/secure
Answer: D
Explanation:
Comprehensive and Detailed Explanation From BIG-IP Administration Control Plane Administration documents:
On BIG-IP systems, authentication and authorization events are logged in /var/log/secure. This includes:
Successful and failed SSH login attempts
Invalid user authentication attempts
PAM (Pluggable Authentication Module) authentication failures
Access denials related to secure services
Why the other options are incorrect:
/var/log/messages contains general system messages and service events, not detailed authentication failures.
/var/log/audit records administrative configuration changes (who changed what and when), not login attempts.
/var/log/ltm logs traffic-management (TMM) and application-related events.
Therefore, the correct log file for investigating unauthorized SSH login attempts is /var/log/secure.
NEW QUESTION # 45
A BIG-IP administrator is troubleshooting inconsistent configuration objects on devices in a device group.
The administrator uses the command:
tmsh run /cm watch-devicegroup-device
and observes the following output:
devices <devgroup> device clu_id cl_orig cl_time last_sync
20:21 sync_test bigip_a 3273 bigip_a 14:27:00
20:21 sync_test bigip_b 1745 bigip_b 13:52:34 13:42:04
20:21 sync_test bigip_c 1745 bigip_a 13:52:34 13:42:04
What two conclusions can be made about this output? (Choose two answers)
- A. The config from bigip_c was synced to the other devices in the device group during the most recent ConfigSync.
- B. The correct configuration exists on bigip_a and bigip_c because their cluster times match.
- C. The correct configuration exists on bigip_b and bigip_c because their cluster times match.
- D. Two of the devices in the device group have a configuration that is out of date.
- E. bigip_a has the latest configuration.
Answer: D,E
Explanation:
watch-devicegroup-device shows (among other columns) the commit ID (cid.id / shown here as clu_id), the originating device for that commit (cid-orig / shown here as cl_orig), and the time the configuration change was made (cid.time / shown here as cl_time). The highest/newest commit ID and its time represent the most recent configuration change seen among the devices. (clouddocs.f5.com)
* bigip_a has the latest configuration (A) because it shows commit ID 3273 at 14:27:00, which is newer than commit ID 1745 at 13:52:34 on bigip_b and bigip_c. (clouddocs.f5.com)
* Two devices are out of date (B) because bigip_b and bigip_c are still on the older commit ID 1745, so they do not match the latest commit shown on bigip_a. (clouddocs.f5.com) Why the other options are not supported by this output:
* C is not supported: bigip_c is not showing a newer commit than the others; it's on the older commit (1745), so it's not the source of the most recent change. The output's cid-orig column is what tells you where the change was made. (clouddocs.f5.com)
* D/E are incorrect logic: matching cid.time between two devices only indicates they share the same change timestamp/commit, not that it is the correct or latest configuration. The "latest" is indicated by the newest commit ID/time (here, bigip_a). (clouddocs.f5.com)
NEW QUESTION # 46
When looking at this BIG-IP prompt: root@virtual-bigip1] Peer Time Out of Sync What does the message indicate? (Choose one answer)
- A. That the local time is correct, but the remote time is incorrect
- B. That one of the NTP sources has a skewed clock
- C. That there was a time synchronization issue between the BIG-IP device and its peer
- D. That the peer BIG-IP is unreachable for the device group
Answer: C
Explanation:
On BIG-IP systems that participate in a Device Service Cluster (DSC), each device compares the remote device's system time to its own system time. If the difference is outside the ConfigSync time threshold (commonly referenced as 3 seconds by default), BIG-IP updates the shell prompt to show "Peer Time Out of Sync", and ConfigSync operations may fail until time is corrected (typically by fixing NTP reachability
/configuration, or in some cases adjusting the threshold). (cdn.studio.f5.com) This message is specifically about time drift between peers in the trust domain/DSC-not basic reachability (so B is not what it means), and it does not prove which side is "correct" (so C is too specific). It also doesn't directly mean an NTP source is "skewed" (A can be a cause, but the prompt message itself indicates the peer- to-peer time mismatch condition). (cdn.studio.f5.com)
NEW QUESTION # 47
Users report that traffic is negatively affected every time a BIG-IP device fails over. The traffic becomes stabilized after a few minutes. What should the BIG-IP Administrator do to reduce the impact of future failovers?
- A. Configure a global SNAT Listener
- B. Configure MAC Masquerade
- C. Enable Failover Multicast Configuration
- D. Set up Failover Method to HA Order
Answer: B
Explanation:
Comprehensive and Detailed Explanation From BIG-IP Administration Control Plane Administration documents: When a failover occurs, the newly active device must inform the surrounding network that it now "owns" the shared IP addresses. Without MAC Masquerade, the new device uses its own hardware MAC, requiring upstream routers to update their ARP tables (which causes a delay). MAC Masquerading allows the HA pair to share a "floating" MAC address, ensuring the Control Plane transition is transparent to the network layer
NEW QUESTION # 48
The BIG-IP Administrator runs the command:
netstat -an | grep 443
and sees the following output:
tcp 0 0 0.0.0.0:443 0.0.0.0:* LISTEN
What does this output indicate about the service on port 443? (Choose one answer)
- A. The service indicates no connections to the LISTEN port.
- B. The service is actively listening only on the loopback interface.
- C. The service is in a standby state and unable to accept connections.
- D. The service is actively listening on all interfaces for HTTPS traffic.
Answer: D
Explanation:
Comprehensive and Detailed Explanation From BIG-IP Administration Control Plane Administration documents:
In netstat output:
0.0.0.0:443 means the service is bound to all available IPv4 interfaces on the system.
LISTEN indicates the service is actively waiting for incoming connection requests.
Therefore, this output confirms that a service (commonly HTTPS/443, such as the BIG-IP Configuration Utility or an application listener) is actively listening on all interfaces, making B the correct answer.
Why the other options are incorrect:
A would show 127.0.0.1:443 if it were loopback-only.
C is incorrect because LISTEN explicitly indicates readiness to accept connections.
D is unrelated; standby state does not affect socket binding shown by netstat.
Hence, the correct answer is B.
NEW QUESTION # 49
New Syslog servers have been deployed in an organization. The BIG-IP Administrator must reconfigure the BIG-IP system to send log messages to these servers.
In which location in the Configuration Utility can the BIG-IP Administrator make the needed configuration changes to accomplish this? (Choose one answer)
- A. System > Logs > Configuration
- B. System > Configuration > Local Traffic
- C. System > Logs > Audit
- D. System > Configuration > Device
Answer: A
Explanation:
On a BIG-IP system, remote syslog server configuration is managed through the logging configuration framework. In the Configuration Utility, this is accessed via:
System > Logs > Configuration
This section allows the administrator to:
* Define remote syslog destinations
* Configure log publishers
* Control which log types (system, audit, LTM, ASM, etc.) are forwarded to external syslog servers Why the other options are incorrect:
* A. System > Configuration > Local TrafficUsed for traffic management settings, not logging.
* C. System > Logs > AuditDisplays audit log settings and content but does not configure remote syslog destinations.
* D. System > Configuration > DeviceUsed for device-level settings such as hostname and platform configuration, not logging.
Therefore, the correct location to reconfigure BIG-IP to send logs to new syslog servers is System > Logs > Configuration.
NEW QUESTION # 50
A user needs to generate a QKView to upload to iHealth to determine any issues with upgrading TMOS.
Where can the user generate the QKView in the Configuration Utility?
- A. System > Support
- B. System > Software Management
- C. System > Archives
- D. System > Configuration
Answer: A
Explanation:
Generating a QKView is a standard procedure for identifying device health and upgrade readiness42. Within the Configuration Utility, this Control Plane diagnostic tool is located under System > Support43. This utility collects configuration and state data into a single file used by the iHealth 'Upgrade Advisor' to report on known bugs or compatibility issues prior to a version change.
NEW QUESTION # 51
A BIG-IP Administrator needs to verify system time synchronization. Where should this be checked?
- A. System > Logs
- B. System > Software Management
- C. System > Configuration > Device
- D. System > Platform
Answer: C
Explanation:
Time synchronization is a critical component of Control Plane management, as it ensures that logs are accurately timestamped and that High Availability (HA) trust relationships remain valid1.
* Configuration Location: The list of configured NTP (Network Time Protocol) servers and their status is managed under System > Configuration > Device > NTP .
* Procedural Importance: If the system clock drifts significantly between two devices in an HA pair, the Control Plane may experience a "Time Delta" error33. This drift often causes a failure in device trust, preventing the ConfigSync process from functioning correctly.
* System Integrity: Accurate time is also essential for the validity of SSL/TLS certificates used for both administrative management access and high availability communication.
* Verification: Administrators can use this section of the Configuration Utility to confirm that the BIG- IP is communicating with its designated upstream time sources and that the local clock is correctly synchronized to the network environment .
NEW QUESTION # 52
A BIG-IP Administrator is setting up a new BIG-IP device. The network administrator reports that the interface has an incompatible media speed. The BIG-IP Administrator needs to change this setting manually. From which location should the BIG-IP Administrator perform this task?14
- A. In the Configuration Utility, System > Configuration18
- B. In the TMOS Shell Command line16
- C. On the Front Console15
- D. In the Configuration Utility, Network > Interface17
Answer: D
Explanation:
Comprehensive and Detailed Explanation From BIG-IP Administration20 Control Plane Administration documents: Connectivity management involves ensuring that the physical layer matches the networking environment. Interface properties, including media speed, duplex settings, and MTU, are managed at the Control Plane level under the Network menu. To resolve a mismatch with an upstream switch, the administrator must navigate to Network > Interfaces to manually override auto-negotiation settings.
NEW QUESTION # 53
A BIG-IP Administrator suspects that one of the BIG-IP device power supplies is experiencing power outages. Which log file should the BIG-IP Administrator check to verify the suspicion?
- A. /var/log/audit
- B. /var/log/kern.log
- C. /var/log/ltm
- D. /var/log/daemon.log
Answer: C
Explanation:
Although /var/log/ltm is primarily associated with Local Traffic Manager events, it is also the primary destination for system-level alerts generated by the Control Plane's chmand (Chassis Manager Daemon).
Hardware status changes, including power supply failures, fan speeds, and temperature warnings, are logged as "notice" or "critical" events within the LTM log file.
NEW QUESTION # 54
A BIG-IP Administrator needs to restore a UCS file to an F5 device using the Configuration Utility. Which section of the Configuration Utility should the BIG-IP Administrator access to perform this task?
- A. Local Traffic > Virtual Servers
- B. Local Traffic > Policies
- C. System > Archives
- D. System > Configuration
Answer: C
Explanation:
Managing the state of a device often involves restoring configuration backups known as User Configuration Set (UCS) files These archives contain the full system configuration, including licenses and SSL certificates.
The Control Plane provides a dedicated management area for these files under System > Archives, where administrators can upload, create, and restore configuration snapshots
NEW QUESTION # 55
A BIG-IP Administrator needs to check the memory utilization on a BIG-IP system. Which two methods can the BIG-IP Administrator use? (Choose two.)
- A. Go to Statistics > Module Statistics > Memory in the configuration utility
- B. Go to Statistics > Module Statistics > Traffic Summary in the configuration utility
- C. Run the tmsh show /sys memory command
- D. Run the tmsh show /sys traffic command
Answer: A,C
Explanation:
Comprehensive and Detailed Explanation From BIG-IP Administration Control Plane Administration documents: Reporting device status includes monitoring physical resource exhaustion, such as memory48. The Control Plane provides both a command-line method via TMSH (show /sys memory) and a graphical method under Statistics > Module Statistics > Memory to report on how memory is allocated across TMM and the Linux host494949494949494949. This is essential for identifying potential "Aggressive Mode" triggers or hardware performance bottlenecks50.
NEW QUESTION # 56
A BIG-IP Administrator needs to load a UCS file but must exclude the license file.
How should the administrator perform this task? (Choose one answer)
- A. From the CLI with command tmsh load /sys ucs <ucs filename> no-license
- B. From the GUI, select the UCS file, uncheck the license box, and click Restore
- C. From the CLI with command tmsh load /sys ucs <ucs filename>
- D. From the GUI, select the UCS file and click Restore
Answer: A
Explanation:
Comprehensive and Detailed Explanation From BIG-IP Administration Control Plane Administration documents:
When restoring a User Configuration Set (UCS) file, BIG-IP allows administrators to selectively exclude the license during the restore process. From the CLI, this is accomplished using the no-license option with the tmsh load /sys ucs command.
The command:
tmsh load /sys ucs <ucs filename> no-license
restores:
System configuration
Certificates and keys
Device and traffic objects
while explicitly excluding the license file, which is required when:
Migrating configurations between devices
Restoring to hardware with a different license
Avoiding license conflicts or overwrites
Why the other options are incorrect:
A does not provide the option to exclude the license.
B restores the UCS including the license, which does not meet the requirement.
D is incorrect because the BIG-IP GUI does not provide a checkbox to exclude the license during UCS restore.
Therefore, the correct and supported method is C.
NEW QUESTION # 57
In a Palo Alto Networks firewall HA pair, what happens if a configuration change is made directly on the Passive device while Auto-Sync is enabled?
- A. The change will be undone when Auto-Sync propagates the config to the HA pair.
- B. The change will take effect when Auto-Sync propagates the config to the HA pair.
- C. The change will be undone next time a configuration change is made on the Active device.
- D. The change will be propagated next time a configuration change is made on the Active device.
Answer: B
Explanation:
Comprehensive and Detailed Explanation From BIG-IP Administratio24n Control Plane Administration documents: TMOS Device Service Cluste25ring (DSC) allows for configuration changes to be made on any device within a synchronization group. If Auto-Sync is enabled, the Control Plane detects the change on the Standby unit and automatically propagates (pushes) that updated configuration to the other members of the HA pair
NEW QUESTION # 58
......
F5-CA Fundamentals-F5CAB4 Exam-Practice-Dumps: https://examtorrent.actualtests4sure.com/F5CAB4-practice-quiz.html
